Water Filtration by Industry

The cartridge that works in a bottling line is the wrong one for produced water, and vice versa. What changes between industries is not the hardware - it is what is in the water, how hot it runs, and what happens downstream if a cartridge lets solids through. Start from the application and the specification follows.

Desalination & Seawater

Seawater RO trains live or die on pre-treatment. We supply the 5 micron and 1 micron stages that protect the membranes, plus the 4040 and 8040 elements themselves.

Read the guide →

Food & Beverage

Bottling lines, breweries and dairies need cartridges that do not shed fibres and do not leave taste behind. Food-grade PP, carbon block and PES membrane cartridges.

Read the guide →

Oil & Gas

Produced water, injection water and hot glycol or amine streams each need a different cartridge - and the temperature rating usually decides the choice.

Read the guide →

Pharmaceutical & Laboratory

Where the water specification is written into a validation document, you need consistent absolute ratings and batch traceability, not the cheapest cartridge.

Read the guide →
Filter cartridge production workshop with pallet loads and hand trucks

Not sure where your plant fits?

Send us the analysis of the water you are filtering and the flow rate you need to hold, and we will tell you which cartridge and which micron rating we would put in that line - including the cases where the honest answer is that you need a pre-treatment stage before the cartridges, not a more expensive cartridge. Samples of any standard cartridge are free, you only cover the freight.

WhatsApp +86 137 3383 7935  |  [email protected]

Matching the Cartridge to the Duty

The same cartridge behaves very differently across industries, because what matters differs. A brewery cares about consistent quality between batches. A pharmaceutical plant cares about documentation. A surface water plant cares about cost per cubic metre. Choosing a cartridge without knowing which of those is the actual requirement is how buyers end up paying for absolute filtration where a depth filter would have done the job better and cheaper.

IndustryWhat matters mostTypical choice
Food and beverageConsistent quality, no fibre sheddingPP melt-blown or pleated, 1–10 micron
BreweryStable performance across a batch cyclePP melt-blown with a coarser pre-filter
DairyHygiene and cleanabilityPleated or PES with documented material declaration
PharmaceuticalAbsolute rating and documentationPES membrane, material declaration per batch
HVAC and make-up waterCost per cubic metreWound string, graded density
Oil, gas and wastewaterChemical compatibility and dirt loadPTFE where chemistry demands, otherwise depth cartridges

Common Questions

Which cartridge should I start with if I am unsure?

A depth cartridge — PP melt-blown or wound — ahead of whatever does the fine work. Most filtration problems are caused by asking a fine cartridge to do a pre-filter's job.

Do you supply cartridges for pharmaceutical use with full documentation?

Yes. PES membrane cartridges with the material declaration and resin grade supplied, which is what an audit asks for.

Can you recommend a filtration train rather than a single cartridge?

Yes, and it is usually the better question. Send the water analysis, the flow rate and what sits downstream and we will propose the arrangement, not just one part number.

Frequently Asked Questions

What types of water does the oil and gas industry filter?

Three main streams: produced water (to be discharged or re-injected), injection water for reservoir pressure support, and process streams such as glycol and amine solutions. Each has very different contamination - oil residues and high solids in produced water, fine particulates in injection water, degradation products in glycol.

Which filter cartridges work for produced water?

High dirt-holding PP melt blown or wound string cartridges are the usual choice for produced water, because the solids load is high and the cartridge is changed often. Where oil residues must be removed to low levels, a downstream carbon or coalescing stage is added.

What filtration is needed for injection water?

Injection water quality is set by reservoir permeability. For most sandstone reservoirs the target is less than 5 micron absolute, often achieved with a multi-stage train: coarse pre-filtration, fine PP cartridges, and for seawater injection an RO or nanofiltration stage.

Which cartridges handle high temperatures?

PTFE membrane and pleated PTFE cartridges are rated for continuous service at up to 260°C, which covers glycol and amine duties. Standard PP melt blown cartridges are limited to about 80°C, so they are not suitable for hot process streams.

How often should cartridges be changed in oil and gas service?

Change on differential pressure rather than on a calendar. A typical trigger is a 1.0-1.5 bar increase above the clean differential pressure, or any visible breakthrough on the downstream side. In produced water service that can be days, not weeks.

Do you supply cartridge sizes to match existing housings?

Yes. We manufacture standard 10-inch, 20-inch, 30-inch and 40-inch lengths in the common end-cap configurations, so cartridges drop into existing housings. Tell us the housing model and we will confirm the correct option.